袋除塵器工作原理及結構特點 - 諾和環保設備

     我司生產的玻纖袋式除塵器是專為水泥立窯和烘干機廢氣除塵開發的_設備，該設備采用微機控制，分室反吹，定時、定阻清灰，溫度檢測顯示等措施，使玻纖袋式除塵設備在立窯、烘干機除塵中能_、穩定運行，煙囪出口排放濃度低于_規定的150gm/m3排放標準，實際可_不大于50gm/m3。
　　Fiberglass bag type collector our production is designed for vertical cement kiln waste gas dedusting and dryer developed high-quality equipment, this equipment adopts microcomputer control, sectional reverse blow, timing, constant resistance dust, temperature detection and display of such measures, the fiberglass bag type dust removal equipment in shaft kiln, the drying machine in addition to high efficiency, stability operation of dust, the outlet of chimney emission concentration lower than the state 150gm/m3 emission standards, the actual can guarantee that not more than 50gm/m3.
　　該設備可不停機分室換袋，操作簡單，安全可靠，運行費用低，是解決立窯、烘干機廢氣除塵的有效設備。袋式除塵設備的工作原理：由于立窯、烘干機廢氣具有含灰濃度高、風量大、污染范圍廣、濕含量高等特點。給烘干機、立窯煙氣的除塵帶來了_的困難，根據烘干機、立窯的特點，采用上進氣方式，含塵煙氣由上部進入進氣室，部分粗顆粒由于慣性落入灰斗，清灰時因氣流方向與粉塵沉降方向一致，防止了粉塵的二次飛揚。
　　The equipment is not stopping points room change bag, simple operation, safety and reliability, low operating cost, is an effective solution to the shaft kiln, drying machine waste gas dedusting. The working principle of the bag type dust collecting equipment: because the shaft kiln, drying machine with high concentration of waste gas containing dust, air pollution, wide range, high moisture content. It brings a lot of difficulties, kiln gas dust drying machine, drying machine, according to the characteristics of shaft kiln, the gas, dust containing gas into the chamber from the upper portion of coarse particles due to inertia, falling into the ash bucket, ash and dust deposition due to the airflow direction is consistent with the direction, to prevent the two flying dust.
　　袋式除塵設備的結構特點：袋式除塵器的基本結構由3個部分組成，玻纖袋式除塵設備的進氣、排氣及反吹系統：包括進氣管道、進氣室、反吹閥、反吹風管、三通管、排氣閥、排氣管。袋室結構：包括灰斗、檢修門、本體框架、上下花板、濾袋、袋室。排灰系統：包括排灰閥、螺旋輸送機。玻纖袋式除塵器本體為全鋼結構，外殼采用輕質巖棉板保溫，保溫厚度為100mm，外殼用δ 為0.5mm 鍍鋅板保護。
　　The structure characteristics of the bag type dust collecting equipment: the basic structure of bag type dust collector is composed of 3 parts, fiberglass bag type dust collecting equipment inlet, exhaust and reverse blowing system: including the inlet pipe, an air inlet chamber, reverse blow valve, anti blowing pipe, three way pipe, the exhaust valve, exhaust pipe. Bag: chamber structure comprises an access door, frame, body, upper and lower plate, filter bag, the bag room. The ash system: including the ash valve, screw conveyor. Ontology fiberglass bag type collector for the whole steel structure, the shell adopts light rock wool insulation, the insulation thickness is 100mm, shell with δ 0.5mm galvanized sheet protection。